July 2020 – More Whazzup at CRAVE Guitars

Prelude

HELLO AND WELCOME to the second half of 2020 for what it’s worth. The fact that most of us meek hominids have made it this far is surely a good thing (for mankind, if not the planet), despite the best efforts of coronageddon. At the time of writing there are over 17 million confirmed cases and 667,000 deaths recorded globally due to coronavirus and sadly the numbers are still rising. I hope you are surviving amongst the mercenary madness. Thoughts, as always, lie with those affected directly and indirectly. Also, it is important to recognise the detrimental effects of the COVID pandemic on mental health & wellbeing; the risk of long‑term psychosis is a concern, worse because it cannot be seen and is rarely disclosed as an issue. Civilisation still has some way to go before it can prove resilient to the virus and worthy enough to survive as a species.

Before further ado, let’s move forward to the past. In the last article, I covered the key acquisitions made by CRAVE Guitars during 2019. As signposted last time, this month I’ll be covering the experience of repatriating 42 guitars and basses (40 of them vintage) after an extended period in enforced storage and bringing them back to as good a shape as they can be. None of the guitars covered here were featured in last month’s article, so there is no overlap between the two.

What are we actually talking about here?

As a reminder, here is the full list of the guitars that eventually returned home (by brand/alphabetic order):

Vintage Fender guitars (13):
  • 1966 Fender Coronado II
  • 1965 Fender Duo-Sonic II
  • 1965 Fender Jaguar
  • 1965 Fender Jazzmaster
  • 1965 Fender Musicmaster II
  • 1966 Fender Mustang
  • 1972 Fender Mustang Competition
  • 1977 Fender Stratocaster
  • 1983 Fender Stratocaster ‘Dan Smith’ Era
  • 1988 Fender Telecaster
  • 1974 Fender Telecaster Custom
  • 1973 Fender Telecaster Deluxe
  • 1972 Fender Telecaster Thinline
1966 Fender Coronado
Vintage Gibson guitars (20):
  • 1983 Gibson Corvus II
  • 1963 Gibson ES-330 TDC
  • 1985 Gibson ES-335 Dot
  • 1983 Gibson Explorer
  • 1984 Gibson Explorer
  • 1982 Gibson Explorer CMT/E2
  • 1984 Gibson Explorer Custom Shop Edition
  • 1984 Gibson Explorer ‘Union Jack’
  • 1976 Gibson Firebird Bicentennial
  • 1966 Gibson Firebird III
  • 1980 Gibson Flying V2
  • 1989 Gibson Les Paul Custom
  • 1977 Gibson Les Paul Deluxe Gold Top
  • 1975 Gibson Les Paul Standard
  • 1964 Gibson Melody Maker
  • 1961 Gibson Melody Maker D
  • 1982 Gibson Moderne Korina Heritage
  • 1981 Gibson RD Artist
  • 1965 Gibson SG Junior
  • 1968 Gibson SG Standard
1981 Gibson RD Artist
Vintage other brand guitars (5):
  • 1966 Epiphone Olympic
  • 1962 Gretsch 6120 Chet Atkins Double Cutaway Hollowbody
  • 1965 Gretsch 6135 Corvette
  • 1974 Rickenbacker 480
  • 1964 Silvertone 1449 ‘Amp in Case’
1974 Rickenbacker 480
Vintage basses (2):
  • 1977 Fender Precision Fretless Bass
  • 1978 Music Man Stingray Bass
1978 Music Man Stingray Bass
Non-vintage guitars (2):
  • 2002 Gibson Les Paul Standard
  • 1998 Gibson Les Paul Standard DC
1998 Gibson Les Paul Standard DC

Many purists may assert that some of these aren’t ‘vintage’. However, that is a debate for another time and place (and has actually been deliberated upon in previous articles). CRAVE Guitars’ cut‑off point is currently the end of 1989, i.e. over 30 years old.

While I might bloviate limitlessly about these musical devices, you will probably be relieved that I won’t be going through each of the guitars in sequence and in forensic detail. Rather, I will try to relate the key headlines, the highs and lows, the learning points and any resultant implications arising from the exercise.

At the time of writing, 38 vintage guitars have been given a well-deserved cossetting and these are the ones I’ll be covering here. The only ones remaining are the two vintage bass guitars, which I dread will both need some expert remedial work, as well as the two newer guitars (1998 and 2002). These remaining instruments will get the treatment they require in due course but now is the time to reflect on the significant work done on the major assets. I abhor calling them that but in this context, I guess that’s what they are.

Where they went and how they returned

In this first section, I may reiterate some points I’ve previously covered, so for regular readers, please forgive me for repeating myself. The elephant in the room is… ‘why?’.

I have to admit that the events that led to ‘here & now’ include a very dark period for me and the impact of the hardship still deeply affects me to my core. I won’t go into the detail of the circumstances, suffice to say that I lost pretty much everything back in 2011 and rapidly had to find a temporary home, not only for us as a family, but also for most of my guitars, which at that time was around 37 of them.

My first job was to document what was going away as best as I could, which included photographs and a comprehensive database covering each guitar. Fortunately for me, a good friend was able to find a safe space for them and they were stored away in a dry and reasonably ventilated roof space. Certainly not the ideal conditions for temperature and humidity but when desperate needs must, it was a saviour of momentous proportions and for which I will be eternally grateful. At least we live in a cool temperate zone, so the swings in climate could be a lot worse.

I had hoped to get back on my feet in a matter of just a few months, however that turned into a year and then several years until they were brought back home in 2019. I felt truly bad about the imposition on my friend and very fearful about what deterioration might be taking place in a less than perfect environment over an extended period of confinement. At least the guitars were all in cases of one sort or other, offering some degree of protection. During the lengthy hiatus, some guitars were retrieved, others swapped out and some were interred. Some of them, however, spent the full 7‑8 years in horrible exile.

We eventually relocated into a new home in the SW of the UK in 2017. When we moved, a few of the newer non‑vintage gear had to be sold off to preserve the core vintage items. A year after our move, my friend also moved home, staying in the SE of England. It was that combination of events that led to ‘the 42’ and I being reunited at long last in January 2019. A specialist haulage company charged the Earth for the pleasure of transporting them 200‑odd miles but at least they arrived OK. I had originally planned to refurbish our damp, dark cellar to make a new home for the guitars first but, as is usually our luck, circumstances got in the way and now I’m living amongst many stacked guitar cases. At least they are always close to hand.

Repatriation Guitar Cases

I knew that it wasn’t just going to be a case of unpacking and playing them as if nothing had happened, so I set about planning a very unhurried and practical approach to assessment and reconditioning. There was no set order to this process; it was very much a case of starting at the beginning and working through in whatever order they happened to be in. Now, in July 2020, I have worked through all the key returnees.

Nevertheless, it has taken over 18 months to complete the programme of refurbishment to this point. Not a quick procedure but not rushed either. I always felt that it would be better to take it easy rather than potentially to make things worse by jumping in too enthusiastically. They are already old, a little longer doesn’t matter.

General Condition

Thankfully, all the guitars were in cases, although the condition of each case varied greatly. Some cases are good and strong, while others have various signs of wear and tear and some are very tatty and weak, providing hardly any physical protection but better than nothing. The oblong cases were far easier to accommodate, being easier and safer to stack, unlike the shaped ones.

The first thing to notice was a predictable coating of general entropy. A lot of people pay a lot of money for genuine old dust and grime (heehee), so the cases stay as they are, as testament to the trials and tribulations to which they had been exposed. I am not one of those snobbish ‘collector’ types that insist on everything being perfect and as‑new. I fully understand that I am only a temporary custodian in their long lifespan that in some cases started before I was born and which most likely will well outlast me. This part of their existence has at least been documented for all to see. It is all part of our collective heritage, albeit a miniscule representation.

Opening each case for the first time and taking each guitar out was the point of maximum trepidation and anxiety, rather than excitement. On initial release, each one was given a cursory once over to see if there was any immediate and obvious appreciable damage. I can report that, so far, that no appreciable impairment has occurred to any of the guitars during stasis. No significant issues requiring immediate corrective work were noticed, which was a massive relief. Phew!

One thing common to many, if not all, guitars was an unidentified surface film/smear, despite being effectively protected from too many outside elements. There were also signs of varying degrees of oxidation and/or corrosion to some metal parts although, again, nothing particularly serious. Most of these ‘issues’ would be rectified by a sensitive clean. A few guitars seemed to have more nitrocellulose weather checking than I remember. Whether this was a result of inaccurate memory or a genuine reaction to environmental factors, I cannot be absolutely sure. While finish crazing can add mojo to a vintage guitar, I’d rather not intentionally make it worse, so I was a bit despondent on that front, as the crazing process is irreversible. So, job number 1 would be a thorough deep cleaning – not enough to ruin the genuine patina of age but just to bring the finish back to life and protect it for the future.

1984 Gibson Explorer

The next thing was a quick acoustic strum and noodle before plugging them in. All of them were strung at full tension to preserve the neck relief but the strings themselves showed various degrees of corrosion and were horribly sticky to the touch. What surprised me was that about 80% of them were still in tune. Impressive. They sounded dead and lifeless though, even acoustically. So, job number 2 would be a full restring and setup for each of them.

Each guitar was then plugged in to an amp to test the instrument’s electrics. This is, sadly, where the most obvious degradation was evident across the board. Initially, some showed no signs of electrical life at all, which was a concern. Others had annoyingly intermittent noisy signals, many had rough scratchy pots, iffy crackly switches and raucous jittery jack sockets. I don’t think that any permanent failures occurred although they clearly needed to be seen to before they could be used in earnest. To be honest, with unkempt electrics and long dead strings, they generally sounded awful compared to how they should be. Not a promising initial analysis. So, job number 3 would be to go over the electrics where necessary to return them to usable operation.

That’s about it. Thankfully, there were no major concerns other than any reservations I might have had anyway (these are vintage guitars after all). The appearance could easily be resolved through some sensitive tender loving care (TLC). The electrics, I was pretty sure could be cleaned up and just used. Restringing and setting them up properly would, I hope give them a new lease of life. Phase 1 sorted then – just 3 key straightforward tasks for each guitar plus anything specifically identified on each one as they went through the TLC procedure.

Playability

As mentioned above, straight out of storage, pretty much every guitar felt dead and lifeless with little resonance from the bodies. Anyone who has followed CRAVE Guitars over the years knows that it is my firm belief that guitars should never be kept as mere trinkets and they need to be played regularly. The guitars seemed to agree wholeheartedly with this observation, as they were telling me loud and clear that they didn’t appreciate not being used for so long. It makes me wonder how many would‑be collectors are put off vintage guitars because they try one out in this unprepared state and then presume that they are all like that.

As I wasn’t in a hurry, I experimented with my approach to this zombie‑like phenomenon. They are just bits of wood, metal and plastic after all; why should a period of abandonment make that much difference? What is it that makes the difference? I decided to take some amateur and idle investigation a little further.

1983 Gibson Corvus

Some guitars I stripped down straight away, while others I decided to play for a while before reconditioning them. The interesting thing is that they didn’t need cleaning or restringing to bring them back to some resemblance of vitality, they simply needed playing for a while. Even with ratty old strings, tarnished finish and creaky electronics, they surprisingly would recover much of their vibrancy after a few days of being used. Some needed more teasing than others – no surprise there. This doesn’t mean that they couldn’t be made even better. Those that were given some TLC first seemed to spring back a bit quicker and stronger with fresh strings on board.

Most of the guitars did not need much in the way of set up to restore their playability. Not one needed a truss rod adjustment (phew!). I suppose the necks have been OK for several decades and they had already settled into how they should be. However, restringing gave an opportunity to check action, nut, bridge saddles, intonation and pickup height to fine tune them. A couple needed appropriate lubrication for the nut, bridge and tuners but not much. Time for some D’Addario/Planet Waves ‘LubriKit Friction Remover’, especially on vibrato‑equipped instruments. Just a few simple things made a lot of difference.

However, getting back to the point, the biggest difference to usability was simply to play them for a while. The comparison between ‘before’ and ‘after’ was remarkable in almost every instance. I’m sure that there must be scientific reasons but I’m not clear in my mind what actual cause and effect is going on here.

General TLC

This is the bit of maintenance that I’m probably best at – the simple stuff. I have mentioned quite a few times that my practical guitar tech skills are limited. What I can do though, is to give guitars a thorough pampering. The first thing is to take the old strings off (and recycle them). Some needed a bit of extra dismantling, for instance to get at the electrics, to shim a bolt‑on neck or to capture neck/body codes and document internal condition.

Cleaning is a relatively straightforward and painless process but it does make a huge difference to aesthetics. If there were specific reasons to do so, I might start off using T‑Cut judiciously to get through thick grime or smooth out some minor scratch marks. However, T‑Cut isn’t recommended to use on vintage guitars but it can help in some circumstances, as long as one is very careful. I have tried other abrasive products with varying degrees of success.

Most of the cleaning process was done using my guitar maintenance ‘system’ of choice, which is D’Addario/Planet Waves products.

More gentle than T‑Cut is D’Addario’s ‘Step 1 Restore: Detailer’, which is good for restoring the underlying nitrocellulose finish without ruining the natural aging and patina that develops over many years. It also helps to reduce minor swirl or plectrum marks, giving a nice healthy overall sheen. The degree of elbow grease required depended on each guitar and it is worth it.

After leaving the finish for a day to stabilise, I then used D’Addario’s ‘Step 2 Protect: Guitar Wax’, which uses premium quality Brazilian carnauba wax to give it a lovely finish and protect it for the future. As a wax, I’m uncertain as to how effective it actually is on nitrocellulose or polyester finishes but I figured that it certainly can’t do any harm. It is important here not to use anything that contains silicon or other unhelpful contaminants.

At this point, I would stop and not use D’Addario’s ‘Step 3 Shine: Spray Cleaner’ unless I continued to play the guitar for some time. It is ideal for use when a guitar needs a quick spruce up after playing, before putting it back into its case and/or moving onto the next one.

Plenty of people prefer other maintenance systems such as Dunlop’s excellent cleaning products. I just prefer the ’Addario/Planet Waves’ products. It may seem like I’m promoting and/or recommending their products, I’m not – it just works for me. They are quite expensive per millilitre but I think worth it on balance.

All rosewood and ebony fingerboards needed a good clean and multiple applications of lemon oil (which, incidentally, ain’t what it used to be!). Here, I use Kyser Lemon Oil, now that I’ve run out of my old good stuff, which it seems you can’t get any more. I’m still looking for something better though. Maple fingerboards only needed the same cleaning as for body/neck finish and it is important not to use lemon oil on lacquered maple fingerboards.

The condition of frets unsurprisingly varied from guitar to guitar, especially in the lower ‘cowboy chord’ frets. A few will require expert fret work at some point but not immediately. There were a few signs of rough surface corrosion. At its worst, rust build up could be removed using very fine grade wet & dry paper, whereas routine sprucing up could be achieved with fine wire wool depending on condition. For a final gleam, I used D’Addario’s ‘Fret Polishing System’. Visually, it does make a difference and it makes playing much nicer, especially when string bending in the higher registers.

Most of the other metalwork was OK and nothing needed anything radical. One has to be careful on gold, chrome or nickel plating, not to abrade the surface too much, so a gentle application of Brasso Metal Polish wadding was usually enough to remove surface tarnish and restore a nice metallic shine. I didn’t need to go further and use something harsher like Solvol Autosol on any guitar metalwork.

The crackly, glitchy, scratchy electrical components, including the usual pots, switches and jack sockets were mostly solved with a dose of electrical contact cleaner and repeated use to clean the surfaces. Here, I use Tone Electro-Sound Guitar Pick-Up & Electronic Cleaner, which is expensive but cheaper than the class leader, DeoxIT. There were a few remaining electrical problems that will require soldering and/or replacement parts/wires but nothing requiring immediate attention. As they were mostly OK when they went into confinement, it was really only new issues that will need sorting out.

1965 Fender Duo-Sonic II

As I’m sure most guitarists will attest, new strings are a key part of the playing experience. Here, I am very pragmatic and don’t insist on a ‘must have’ type of string. I am certainly not a string snob, opting for some (expensive) esoteric boutique product that needs changing after every play. Frankly, I can’t tell the difference. What I will mention is that it requires a level of investment to restring 40+ guitars, especially without ready access to bulk buying as a regular end‑consumer.

For Stratocasters with a vibrato block, I generally use Fender Bullets 10‑46 gauge. For most standard scale guitars, I use Ernie Ball Regular Slinky 10‑46 gauge. For short scale guitars or ones that benefit from a little extra string tension, I’ll go up to Ernie Ball Power Slinky 11-48 gauge. For the Gibson ES‑150, I haven’t decided on a suitable string set yet but it will probably need something like 12-56 semi‑flat wound strings to give it the necessary volume, warmth and resonance that it deserves. With the dreaded Brexit negotiations and no clear trade deals with either the European Union or the U.S.A. (or anyone else for that matter), I may decide to migrate to British‑made Rotosound strings for general use.

A final buffing with a lint‑free duster keeps the guitar’s finish nicely clean and shiny. No guitars are going back into long‑term storage and all will be played regularly over time. They aren’t on constant display and are kept indoors in their cases when not being played.

Remedial Work

Most of the guitars were in pretty good condition when they were stored away, so they didn’t go into incarceration with (m)any outstanding issues. Fortunately, they also came home in pretty good condition too. As mentioned above, I think both basses need some expert attention to their necks. I can’t be sure what issues they may have or what may be required but it is probably best to leave that to the experts.

There are a few guitars that do need electrical work doing, once again, anything beyond cleaning up contacts is best left to the experts. Some have intermittent problems (hums, crackles) or weak signals. On some, the balance of tones doesn’t seem right and could do with investigation. Perhaps some combination of new pots, switches, wires, capacitors, jack sockets, solder joints, etc. may be required.

If replacements and/or repairs are needed, where possible, these will be vintage correct. However, finding genuine vintage parts in the UK is a big issue and importing them is disproportionately expensive, so it isn’t something to be taken on lightly. In several instances, I may have to be pragmatic and replace faulty vintage parts with newer quality equivalents. After all, it is better to have guitars working properly, otherwise they are just planks of wood, bits of metal and plastic that won’t get played. Things like vintage pots can always be fitted retrospectively if need be.

Apart from the basses, not one of the guitars suffered neck problems, which I am genuinely amazed at. I guess they were old and settled anyway. Certainly no fretwork will be needed other than some basic levelling, crowning and polishing. I wish it was something I felt more confident about doing myself but I know that, if I made a mistake, it would undoubtedly be worse than when I started. Best left to a competent technician.

None, thankfully, require any finish work. I would prefer to leave any worn finish, dinks, scuffs, scratches or other marks as they are, rather than refinish a guitar and ruin its authenticity. Besides, I am smitten by the untold stories behind the genuine blemishes and imperfections that give them character. These are not new guitars and neither should they look it. Neither are they museum pieces, so the ravages of daily use are important to both their integrity and charm.

I only have one refinished guitar, which is CRAVE Guitars’ ‘signature’ 1975 Gibson Les Paul Standard. The guitar came to me when it was about two years old and had significant buckle rash on the back. For a while, it was finished in natural before being refinished again in a beautiful cherry sunburst. If you are wondering, it was originally a dark tobacco sunburst. At the time, as a teenager, I didn’t know any better and had absolutely no idea that in several decades that I would a) still have the guitar or b) value original finishes. Oh well. One lives and learns.

1975 Gibson Les Paul Standard

Guitar cases are a different matter. Some of the very old ‘cardboard’ cases are pretty tatty and there is not much that can be done about that. A number of cases have broken latches or missing handles and I would like to work through these to make them at least usable. Sourcing vintage or OEM NOS parts and restoring the hardware isn’t easy, as latches, hinges and handles were mainly riveted on, rather than screwed. Again, this isn’t entirely necessary or urgent, so it can be a project for a future date. Mostly, they are best left as they originally came to me.

Parts and Accessories

There are a few guitars that have had newer parts fitted at some point (not by me, I might add!). Some of these examples could do with sensitive conservation by using vintage original replacement parts. None of this is necessary or urgent so, like several other jobs, it can be done over time as opportunities present themselves. Messing with them or modifying them is not on my agenda.

Case candy is always nice to have but I don’t go out of my way to acquire it, if it wasn’t original to the guitar. Authenticity matters here. We have more than enough fake news and phoney history to contend with, without adding unnecessary doubt to the origins of the guitars.

Some have optional parts missing, for instance, my 1977 Fender Stratocaster doesn’t have its original bridge cover but, let’s face it, does it really matter? It may be another ‘nice to have’ but it serves absolutely no beneficial function.

1977 Fender Stratocaster

Many of the guitars have their original cases but, similarly, many came to me with non‑original or modern cases. While I might like to get vintage original cases for some guitars, that can be inordinately expensive and it kinda messes with originality. Another ‘nice to have’ but not essential. If an occasion comes along to conserve the instrument better, I’ll consider it as and when. It really is the contents that matter.

If I’ve done my buying well in the first place, the acquisition of parts and accessories to restore a guitar to as close to its original condition generally aren’t needed. There are always exceptions to each rule, so it’s on a case‑by‑case basis.

Documentation and Photographs

By now, you’ll have hopefully concluded that they are all in more‑or‑less acceptable playable condition. Everything else is a bonus.

All that is left to do is to document each guitar at this particular point in time. As mentioned above, when the guitars went into storage, they were photographed and their individual characteristics logged onto a comprehensive database. Now, several years later, some of the details on the database can be updated and, where information was missing, new data can be added.

CRAVE Guitars – Database

New photographs have been taken for historical evidence and also added to the database. In the event of some potential future catastrophe such as theft or damage, all the necessary details will be available. Many of the same photographs can also be used on the web site to go with new all‑new features that have been written. I will come back to the web site in due course, so that’s enough on that front for the time being.

In addition, and perhaps more interestingly, this article and the documentation are all part of each these guitars’ long life stories and something that can go with them if and when they ever get passed on. Perhaps for the first time in their long lives, there is a written and photographic moment‑in‑time record for these wonderful heritage artefacts. This extensive task is still only partially completed but there is no ‘burning bridge’ imperative to hurry the task and it can be done at leisure.

The one I couldn’t put down

Rediscovering these lovely vintage guitars all over again was a real pleasure and there weren’t really any major surprises or disappointments. I wasn’t planning on comparing or ranking the returnees. There was, however, one guitar that stood out above all the rest during the process.

It was… drum roll please… the cool 1965 Fender Jazzmaster. It is an all‑original, pre‑CBS standard sunburst Jazzmaster, so there is nothing particularly unusual about it to differentiate it from any other of the period. Once it was resurrected, fairly nearly the end of the programme, it was the one that I just couldn’t put down and I kept playing and playing if for several weeks before I was compelled to move on. The Jazzmaster must have had some fairy dust sprinkled on it for it to stand out from very tough competition.

1965 Fender Jazzmaster

I consider myself to be very fortunate not only to have had all the guitars but also to re‑experience them for a second time. I am therefore largely content with my lot, despite the hellish privations in getting through the wicked times to this redemptive point.

What next?

Well, the obvious next thing to do is to play and enjoy them. That is, after all, the whole point of having these things in the first place, isn’t it? They can’t all be played at once, so organising them so that they can have equal opportunity for playtime will be important.

That brings us back to an oft‑repeated bugbear of mine, which is my priority to refurbish the house’s currently unused cellar to make a safe and secure home for them all. In the meantime, they are arranged not too badly, so they can be accessed without too much heavy lifting.

While I have worked through the vast majority of the repatriated guitars, these only represent about two thirds of all the instruments here at CRAVE Guitars. There are also the other 24 guitars (and counting), some of which could well do with the same sort of pampering that the returnees have had, and some also need similar remedial work to, for instance, frets, electrics, etc.

1967 Gibson Melody Maker SG

I think the cycle of TLC is a continuous one. Once one cycle has been finished, it will be time to start another one. It is a bit like the metaphor of ‘painting the Forth Bridge’, i.e. an on‑going, repetitive and never ending process. Almost the definition of Sisyphean. At least it is a pedestrian task that I can enjoy as therapy from the mad, mad world unravelling outside my little hikikomorian bubble.

While the focus of this article has been on the guitars, there are also effect pedals and amplifiers that need regular attention and some of which were repatriated alongside the guitars. The same basic principles apply to keeping them in tip‑top shape, even though their needs are different.

I don’t need to sell any guitars although a bit of rationalising and trading up may actually be a good idea. The thing is that I’m not one of those people who regularly buys and sells to keep a constant flow of ‘new’ (to me) guitars coming through. I tend to grow an attachment to guitars, and especially these guitars that have been through so much at my expense. There is maybe a small number that I could part with to make space for something else. It’s just whether I can break the emotional ties. Oh, that and the impending global recession will undoubtedly have a bearing on matters.

There will also inevitably be further additions to the ‘collection’ in due course. I can’t see it getting smaller but I can certainly envisage it getting bigger. However, due to the finite constraints of space, time and money, buying anything else is on hold for a while out of plain old and boring necessity.

Help Needed

I mentioned in the last article that vintage guitars, effects and amps need expert attention from time to time to keep them working at their best, so this is basically a reiteration. If there is someone out there with the requisite skillset to help maintain these treasures, and who is local to SE Cornwall in the UK, I would be interested in exploring opportunities. Is there anyone out there attracted to the proposition? If there is, please contact me at the e-mail address at the bottom of every page on the website.

Learning points

Well, having gone through all of the above, I must have learned something, right?

Probably the most important lesson is simply, ‘don’t do what I did’. Don’t store guitars away for long periods, especially in inappropriate environmental conditions. I couldn’t help what happened to me and I did what I had to do using my best judgement at the time. In retrospect, I am not sure what I could have done differently and retain the guitars. I ‘swear to God’ that I don’t ever want to go through that experience again.

The second lesson is ‘to take your time and not rush in’. To do so would risk the integrity of the guitars. After all that time away, a few more weeks waiting to be sorted out made no difference in the big picture. A measured approach worked wonders and also took a lot of the potential stress out of the process. In effect, instead of a single insurmountable task, breaking it down into manageable steps made it more of a therapeutic and cathartic exercise.

The third lesson is to ‘do what you can and do not do any more’. Leave the other stuff to the experts. Be prudent and cautious about what you undertake. Any foolish actions might well prove to be irreversible and therefore regrettable. One also really doesn’t want to make them look like new; they are old and they are meant to look and feel that way. Conserving these artefacts is important, while preserving them (proverbially ‘pickling them in aspic’) is not. Sensitive refurbishment means accepting that what they are is a direct result of what happened to them and to be happy about it. That doesn’t, however, mean that they should now be neglected all over again. They can be played, enjoyed, maintained and kept in good condition, no problem. They’ve survived this long; my job is to ensure that they survive for a long time after me.

That is really it. Three fundamental, profound and straightforward learning points. Simples! The vista of glorious vintage guitars has been re‑opened to me, so that is one thing to celebrate for sure. The haptic experience of playing these gracefully aging instruments has been restored at long last.

Tailpiece

So, that represents some of their story, revealed at long last. After a year‑and‑a‑half, I can finally say that I am relatively pleased with how things are and no longer over‑anxious about what I might find. Why am I not over the moon? Any overwhelming joy or excitement has been surpassed by the detriment of the past decade that I cannot obliviate.

There is still plenty to do, even in one’s splendidly isolated silo of virus‑induced exile. The short‑term aim is largely to continue on the path already set, while also looking forward more ambitiously to the medium‑to‑long‑term future. I have a plan; it is executing the plan that is the problem. That, ultimately, comes down to filthy lucre.

Anyway, that’s two out of the three catch‑up topics now dealt with. I hope you’ll be willing and able to return for another tasty course of ‘whazzup’ delights next month.

Stay safe and hope you continue to survive the coronapocalypse. Remember that the basis of karma is to ‘be good and do good’. Until next time…

CRAVE Guitars’ ‘Quote of the Month’: “Addiction to false beliefs is equivalent to wronging the world’s rights”

© 2020 CRAVE Guitars – Love Vintage Guitars.

← Return to ‘Musings’ page

Like it? Why not share it?